|
T1 Circuit Extension Over IP Interconnect for Voice and
Data
 The
IP•Tube DLT1-Ecan
encapsulates full and fractional T1 and TDM circuits into IP
packets.
T1 Over IPconnections provide for the interconnection of PBXs and
Telecom Switches via LANs, WANs, MANs, and Wireless Ethernet.
The IP•Tube DLT1-Ecan ships with two T1 interfaces
with either 1 or 2 active and two 10/100 BaseT Ethernet
interfaces.
The inactive T1 Port can be activated via a software-based license key
for a pay as you grow option.
Part No.
|
Model No.
|
Description
|
Retail
|
29-8509
|
IP Tube
DLT1-Ecan
|
T1 Circuit Extension
over IP
Interconnect for Voice and Data
(Two required for link)
T1 Circuit Extension
Over IP for Voice with Echo Canceller
(Two required for link)
• ROI measured in weeks
• On-board
Echo Canceller
• Supports
Legacy Switches/PBX
• Crystal
Clear Voice across Internet
• Exploits
efficiency of IP/Ethernet
|
2,995.00
|
| 29-8510 |
IP Tube
DLT1-Ecan-ALT
|
IP-Tube DL Alternator
Load Balance Option
|
1,200.00
|
| 29-8511 |
IP Tube
DLT1-Ecan-PRO
|
IP-Tube DL Protector
Auto Protection Switch Option
|
1,000.00
|
| 29-8512 |
IP Tube
DLT1-Ecan-SWT
|
IP-Tube DL Switch
Option
|
700.00
|
29-8513
|
IP Tube
DLT1-Ecan-LPT
|
IP-Tube DL Link
Protector Option
|
1,500.00
|
29-8502
|
IP Tube-QT1, 1T1
|
T1 over IP - 4 T1 (one
active), 1 10/100BaseT Ethernet
T1 Circuit
Extension over IP for voice and
data-
4 T1 (one
active), 1 10/100BaseT Ethernet
• ROI
measured in weeks
• Exploits
efficiency of IP/Ethernet
• Supports
Legacy Switches/PBX
• Straight
Forward Configuration
|
2,095.00 |
29-8503
|
IP Tube-QT1,
1T1,
Compr.
|
T1 Circuit
Extension over IP - 4 T1 (one
active),
1 10/100BaseT Ethernet, with Compression
|
3,295.00
|
29-8504
|
IP Tube-QT1, T1
U/G
|
T1 Port Upgrade, Per
Port Activation Key
|
1,600.00
|
29-8505
|
IP Tube-QT1,
Compr. U/G
|
Lossless Data
Compression Upgrade, Per Port Activation Key
The
IP•Tube DLT1-Ecan-C continuously detects idle and redundant data within
each T1 Voice circuit resulting in as much as a 56 to 1 bandwidth
savings. TDM over IP WAN bandwidth is not consumed by silent or
redundant circuits. Note: Compression only supported with
IPTube•DLT1-Ecan-C models. |
1,200.00
|
29-8506
|
IP Express-XL-T1
|
IP WAN Router - 1 T1
integrated CSU/DSU, 1 10BaseT Ethernet |
1,195.00
|
29-8507
|
IP
Express-MLT-DI-HUB
|
IP WAN Router - 2 T1
int. CSU/DSU, 1 10BaseT Ethernet, Drop/Insert/Hub
|
1,995.00 |
29-8508
|
IP Express-QT1,
4T1,
1Eth
|
IP WAN Router - 4 T1
int. CSU/DSU, 1 10/100BaseT Ethernet, MLPPP
|
3,495.00
|
Echo Canceller
The IP•Tube DLT1-Ecan has an integrated T1 Echo Canceller that cancels
up to 64 milliseconds of Far End echo. The echo canceller meets ITU-T
G.164, G.165 and ITU-T G.168 requirements for echo cancellation.
Transparent Interconnect
The IP•Tube DLT1-Ecan’s transparent operation maintains the proprietary
signaling required to support PBX features such as call conferences,
call forwarding, caller ID and SS7.
Signaling Support PRI ISDN, SS7, ESF, D4, SLC-96,
Proprietary out of band, and robbed bit signaling is supported. Echo
cancellation is automatically disabled during FAX and Modem
communications. Transparent support for Modem or Fax. Voice quality is
not compromised. Legacy phone equipment investment is preserved.
IP•Tube
DLT1-Ecan Standard Features
- Assured Delivery
Protocol
In order to assure that circuits are extended over connections with
fault tolerance the IP•Tube DLE1-Ecan has as a standard capability an
Assured Delivery Protocol that supports high performance full duplex
real time data. The protocol has packet out of sequence detection and
re-sequencing, duplicate skipping, and real time lost packet
retransmission with configured delay.
Dual LAN Interfaces
All IP•Tube•DLT1-Ecan models ship with dual 10/100BaseT Ethernet LAN
ports. The dual Ethernet interfaces provide for:
• Management interface on LAN port 2 when LAN port 1 is connected to a
VPN tunnel
• The LAN ports can be configured to support connections over 2
opposite ADSL links
• Alternator Option for load balanced SDSL interconnects
• Protector Option for Redundant Packet Path connections with Constant
or Switch Over Criteria
VPN Network
Management
- Interconnecting
the IP•Tube DLT1-Ecan through a Virtual Private Network with sufficient
real time committed information rate ensures that the required quality
of service is provisioned. The second Ethernet interface provides a
management port. Each LAN interface features independent IP network
Protector
Option
The
protector option utilizes the second LAN interface as a redundant path
for the interconnection of the IP encapsulated T1 Circuit. The
extension of the T1 circuit has a fault tolerant link that is
configured to always on, or with switch over criteria.
-
Pay-As-You-Grow
Field Upgrades
-
The IP•Tube DLT1 Ecan
are designed for Pay-As-You-Go growth from 1 T1 to 2 T1s. Customers can
elect to economize initial installations, buy purchasing a single
active T1 port and enable the additional T1 Port via a software-based
license key.
Field Upgrade benefits are extended to our Industry-Best Loss less Data
Compression. Just as T1 ports are field upgrade able, so is Loss less
Data Compression. At any time, each T1 port on the IP-Tube DLT1-Ecan
can be upgraded to Loss less Data Compression with a simple
software-based license key installation. If you determine that your
IP•Tube DLT1-Ecan is best deployed with Loss less Data Compression,
your still in business with the per port field upgrade!
| Technical
Specifications |
- LAN
Network Interface:
• Two 10/100BaseT Full/Half Ethernet
- •
Autonegotiation or Configurable Speed and Duplex
-
- LAN
Network Protocols Supported:
• IP, TCP, UDP, ICMP
• Assured Delivery Protocol
Echo Canceller:- • Voiceband Echo
Cancelling according to ITU G.165 and G.168
• u- and A-Law coding according to ITU G.711
- • 24 channels
with end echo path delay of less than 63.75 ms
-
- T1/Fractional T1
Specifications:
• One or two Port Models
- • Connects directly to T1
or DS1
- • Framing - ESF or D4
- • Coding - B8ZS or AMI
- • Supports DS0
assignments from 1 to 24
- • Not Contiguous
Configuration x-y,z Supported
- T1 Over
IP Protocol:
- • TDM Over IP
- • Circuit
Extension Services Over IP - CESOIP
- • HDLC Over IP -
HDLCOIP
- • Frames Per
Packet Configurable 8 to 56
- • Low Latency
Mode: 1 millisecond 8 T1 frames
- • Max Payload
Mode: 7 millisecond 56 T1 frames
• Comprehensive Clocking: Internal, Network, Adaptive
|
TFTP
Online Upgrade Capable (FLASH ROMs)
• IPTube is
fully operational during upgrade
Quality of Service Support:
• IP Type of
Service (TOS) CLI configurable • IANA
Registered UDP Port 3175
Regulatory:
• CE
• Safety
-IEC60950
• EMC - CFR 47
Part 15 Sub Part B:2002,
• EN55022:1994+A1&A2, EN55024,
ICES-003 1997, CISPR 22 Level A
• Telecom Part68
Management:
• Telnet support
with Edit and Paste Template Files
• Console Port
for Out of Band Management
• SNMP support
(MIB I, MIB II) with configurable traps
• Remote
config., monitoring, & reset
• Telco Diagnostics: Local Loop, Remote Loop
Rear
Panel/Power:
• 12-24 VAC/VDC,
1.0A. International Adapters Available
• Optional -48V
0.25 Amp
• Dimensions: 9"
(L) x 7.3” (W) x 1.50” (H)
|
|
- Lossless
Data Compression Option:
- • Detects idle
and redundant data within each DS0
• Configurable Silence Detection Range
- • Interconnect
bandwidth is not consumed by silent or redundant data
- • Compression
settings from 8 to 1 to 56 to 1
|
|
|
| IP•Tube
QT1 |
Enable One to Four T1 interfaces for T1 over IP Voice and Data |
The IP•Tube QT1 is
available with one to four T1 interfaces and dual 10/100 BaseT Full/
Half Duplex Ethernet Interfaces. The T1 interfaces have configurations
that for provide independent protocol, compression, packet sizing,
buffering, clocking, framing, coding and channel settings. Enable
additional T1 Ports as needs expand using a software-based license key.
The protocols supported are IPTube, CESoIP, and HDLCoIP.
|
|
| IP•Tube QT1
Features |
| Transparent
Interconnect
The IP•Tube QT1’s
transparent operation maintains the proprietary signaling required to
support PBX features such as call conferencing, call forwarding, caller
ID and SS7. Legacy phone equipment investment is preserved. Transparent
support for Modem, Fax, or Data circuits. Voice quality is not
compromised.
|
| Lossless
Data Compression Option
The IP•Tube-T1C detects
idle/redundant data within each DS0 resulting in as much as 56 to 1
bandwidth savings. T1 over IP bandwidth is not consumed by silent or
redundant circuits. Management of the IP•Tube T1 is accomplished with a
Command Line Interface that is accessed through a Console or Telnet
connection. Common templates provide for cut and Paste configuration.
|
 |
Service
Quality Packet Prioritizing
The IP•Tube QT1 uses the Type of Service byte in the IP packets to
prioritize the encapsulated T1 frames. The setting of the TOS byte can
be used to ensure that the real time TDM data from the IP•Tube QT1 is
ensured high priority. |
Alternator Load
Balancing Option
The IP•Tube Qt1A Alternator option alternatively sends the IP
packetized T1 frames on LAN 1 and LAN 2. The Alternator option enables
fractional and full T1 circuits to be split over two IP WAN connections
such as xDSL. The Lossless Data Compression option can be combined with
the Alternator option to minimize the bandwidth required from the
alternative paths. The cost of interconnecting T1 communication systems
across packetized xDSL is a fraction of long distance leased T1 circuit
costs. |
 |
Pay-As-You-Grow
Field Upgrades
The IP-Tube QT1/ QE1 are designed for Pay-As-You-Go growth from 1 T1
thru 4 T1s per IP•Tube QT1. Customers can elect to economize initial
network installations, by purchasing their IP-Tube QT1 with a single
active T1 port. As the network grows enable additional T1 Ports via a
software-based license key. Field upgrade benefits are extended to our
Industry-Best Lossless Data Compression. Just as T1 ports are field
upgradeable, so is Lossless Data Compression. At any time, each T1 port
on the IP-Tube QT1 can be upgraded to Lossless Data Compression with a
simple software-based license key installation. If upon installation,
you determine that your IP•Tube QT1s are best deployed with Lossless
Data Compression, you're still in business with the per port field
upgrade! |
VPN
Network Management
Interconnecting the IP•Tube QT1 through a Virtual Private Network with
a sufficient real time committed information rate ensures that the
required quality of service is provisioned. The IP•Tube QT1's second
Ethernet interface provides a management port when the first Ethernet
interface is connected to a VPN. Each Ethernet LAN interface features
independent IP network configurations. |
 |
| Technical
Specifications |
LAN
Network Interface:
• Two 10/100BaseT Full/Half Ethernet
• Autonegotiation or Configurable Speed and Duplex
LAN Network Protocols Supported:
• IP, TCP, UDP,
ICMP
1 to 4
Duplicate Packet Transmission:
• Resilient performance through a lossy interconnect.
T1/Fractional T1 Specifications:
• One to Four Port Models
• Connects
directly to T1 or DS1
• Framing - ESF or D4 • Coding - B8ZS or AMI
• Supports DS0 assignments from 1 to 24
• Non Contiguous Configuration x-y,z Supported
T1 Over IP Protocol:
• TDM Over IP
• Circuit Extension Services Over IP - CESOIP
• HDLC Over IP - HDLCOIP
• Frames Per Packet Configurable 8 to 56
• Low Latency Mode: 1 millisecond 8 T1 frames
• Max Payload Mode: 5 millisecond 56 T1 frames
• Comprehensive Clocking: Internal, Network, Adaptive
Rear
Panel/Power:
• 12-24 VAC/VDC, 1.0A. International Adapters Available
• Optional -48V 0.25 Amp
• Hot Standby
with 2nd Power Module
|
Lossless
Data Compression Option:
• Detects idle and redundant data within each DS0
• Configurable Silence Detection Range
• Interconnect bandwidth is not consumed by
silent or redundant data
• Compression settings from 8 to 1 to 56 to 1
TFTP
Online Upgrade Capable (FLASH ROMs)
• IPTube is fully operational during upgrade
Quality
of Service Support:
• IP Type of Service (TOS) CLI configurable
• IANA
Registered UDP Port 3175
Regulatory:
• CE • Safety -IEC60950 • EMC - CFR 47 Part 15 Sub Part B:2002,
EN55022: 1994+A1&A2, EN55024, ICES-003 1997, CISPR 22 Level A
• Telecom Part68
Management:
• Telnet support with Edit and Paste Template Files
• Console Port for Out of Band Management
• SNMP support (MIB I, MIB II) with configurable traps
• Remote
config., monitoring, & reset
• Telco Diagnostics: Local Loop, Remote Loop
Dimensions:
14" (L) x 5.5”
(W) x 2.50” (H)
|
|
